TQ R/C & Hobbies

Tamiya Mini 4WD Asia Challenge 2025 (TMAC 2025)

 

Referring to the announcement made by Tamiya, Inc. in their website : https://www.tamiya.com/english/newstopics/2025/singapore_malaysia_tmac.html regarding the qualification race of Tamiya Mini 4WD Asia Challenge 2025 (TMAC 2025) for Singapore and Malaysia racers, PT Tamindo Plastic Model / TQ R/C and Hobbies, is planning to conduct the qualification race for the racers from Singapore and Malaysia, with the following venue:


Day / Date : Sunday / 08 June 2025
Place : Mall Mangga Dua Square, 1st floor, Hall A
Registration open date: 24 May 2025
Registration closing date: 31 May 2025
Registration google form:

https://forms.gle/ZqUybUaVissSRpbb8

Registration fee: IDR 300,000 per racer, eligible for 20 run

Please kindly note that the organizer reserve full rights to cancel the event should the organizer deem the race participants to be too small and inefficient to conduct the race. We require minimum attendance of 10 racers from each country.  For example, if there is only 10 racers from country X and 2 racers from country Y, then we will only conduct the qualifications from country X only.

Regulation:

1.  Race system is bracket system 4-2-1

Each Racer will buy 1 card for 20 run for Stage 1
Stage 2, each Racer can only have 4 runs
Stage 3, each Racer can only have 2 runs
Stage 4, each Racer can only have 1 run and after this run car will be quarantined

2.  All parts MUST BE Tamiya original parts. 
3.  Racer can use their own rechargeable batteries
4.  Other regulation we will follow TMAC 2025 Stock Class (attached pdf)
5.  Other regulations if not yet stated or unclear, will be informed during the race and all decision from the organizer is FINAL.

Other things to note:

1.  Please note that all racers should bear their own tickets and accomodation to Jakarta.
2.  Winners from the qualifications for position 1-4 from each country, will only be given entry rights. They shall bear their own tickets and accomodations during TMAC 2025 in Taiwan.

U.S. Assault Tank M4A3E2 "Jumbo"

Rate this item
(0 votes)
U.S. Assault Tank M4A3E2 "Jumbo" U.S. Assault Tank M4A3E2 "Jumbo" Length=172mm Image shows finished model.

1/35 Military Miniature Series No.139

 

U.S. Assault Tank M4A3E2 "Jumbo"
Item No:35139
【 A Rather Hefty Sherman 】 The M4 Sherman was the a mainstay of Allied armor units throughout WWII and over 50,000 examples were produced. Many variants were created to meet specific battlefield requirements and among these was the M4A3E2, known to infantrymen as the "Jumbo," which was produced in 1944 to meet requirements for a heavily armored assault tank capable of close infantry support. Armor protection on the front and sides of the hull were increased to 101mm and 76mm respectively. The new cast turret featured 152.4mm side armor, a 178mm thick mantlet, and mounted a 75mm M3 gun. Its powerplant was a powerful Ford V8 engine which pumped out 500hp. Production of the M4A3E2 began in May 1944, with 254 units being delivered by July.

【 About the Model 】 ★1/35 scale plastic assembly kit. Length: 172mm, Width: 78mm. ★The heavy, imposing form of the tank including turret with 75mm M3 gun has been realistically reproduced. ★Turret hatches can be depicted in either open or closed position. ★Gun barrel enables elevation/depression. ★Kit comes with belt-type tracks with realistic details. ★1 driver torso figure and 1 commander figure are included. ★Accessory parts such as spare wheels and crates are also included.

Specifications are subject to change without notice.

Social sharing

Who's Online

We have 581 guests online