TQ R/C & Hobbies

Mini 4WD Product

Lightweight Plastic Spacer Set (12/6.7/6/3/1.5mm) (Fluorescent Green)

Item No: 95443

★Spacers are a vital component in adjusting the setup of roller and brake parts. ★These low-friction plastic parts are lighter than aluminum counterparts for minimal impact upon car speed. ★Molded in vivid fluorescent green.

Compatible Cars
Mini 4WD and Mini 4WD PRO cars

Information is correct as of December 5. Specifications are subject to change without notice.

Star Unit Series No.5

1/8 R/C Dancing Rider (T3-01 Chassis)

Item No: 57405

Lord of the Dance
This R/C model assembly kit creates the Dancing Rider, a supremely fun 3-wheeled model that offers an exciting lean when cornering. An original body is included with the kit, and was designed under the supervision of famed Japanese artist Atsushi Arino. It is molded in lightweight polycarbonate, and comes with a molded driver figure for an extra touch of fun.

T3-01 Chassis: Designed for Fun
The T3-01 is a three-wheeled chassis comprised of two main sections (front and rear) connected by a center link; the front section houses R/C equipment and the power source, while the rear holds the integrated gearbox and motor. Positioned in the back of the front section, the servo applies motion to the rear section, which in turn makes the front lean. Support arms are moved by the servo, and help the model to self-right in the event that it turns onto its side. At the front, a telescopic fork has a built-in coil spring, while the rear features a cam-slide setup with cams on the rotating pitch axis: sliding left and right, they actuate the built-in coil spring to cushion the rear. A planetary differential gear is integrated into the rear axle.

Specifications
★Length: 260mm ★Width: 135mm ★Height: 175mm ★Wheelbase: 196mm ★Tread (Rear): 91mm ★Tire Width/Diameter 21/61mm (Front), 25/59mm (Rear) ★Monocoque Chassis ★Rear-Wheel Drive ★Planetary Differential Gear ★Front Suspension: Telescopic Fork ★Rear Suspension: Cam-Slide ★Gear Ratio = 10.7:1 ★Requires an Electronic Speed Controller (sold separately) ★Type 370 Motor included

Separately Required Items
★2-Channel R/C System w/ESC ★R6/AA/UM3 batteries for transmitter ★Power source

Information is correct as of December 26, 2017. Specifications are subject to change without notice.

Electric R/C Car Series No.653

1/18 R/C King Yellow 6x6 (G6-01 Chassis)

Item No: 58653

★The journey to school would be a whole lot wilder if you were on board the King Yellow! ★A polycarbonate body with separate parts for roof lights and stop sign creates a crazy school bus. ★Power is provided by the G6-01 chassis, a gear-driven 6WD unit with independent 6-wheel suspension. ★Design of the body was overseen by famed artist Atsushi Arino.

Information is correct as of December 11, 2017. Specifications are subject to change without notice.

Limited Edition R/C Product

1/10 R/C Porsche Turbo RSR Type 934 Black Edition (TA02SW Chassis)

Item No: 47362

★This limited edition release evokes memories of a Tamiya classic from the 1970s. ★The model runs on the short and wide TA02SW chassis, with an FRP double deck frame, FRP damper stays, universal shafts and other hi-spec parts! ★Front and rear tires are of different size. They feature tire inserts. ★The Porsche Turbo RSR Type 934 body is molded in clear polycarbonate.

Information is correct as of December 11, 2017. Specifications are subject to change without notice.

Hop-Up Options no.1784

R/C Model Body Reinforcing Clear Tape

Item No: 54784

★Protect and reinforce your precious R/C car polycarbonate body surface with this handy tape. ★Allows swift, discreet repair of areas easily damaged during a drive, such as fender sections. ★Apply to fenders or roof in advance to help stave off damage. ★35mm x 50cm

Information is correct as of December 11, 2017. Specifications are subject to change without notice.

Hop-Up Options no.1785

R/C Model Body Mount Hole Clear Patches

Item No: 54785

Hop-Up Options no.1788

TA07 Carbon Stiffeners (Front)

Item No: 54788

★Install in place of kit standard K4, K6 and K7 parts. ★Stiffeners boost front rigidity for stable handling. ★Use them to enhance your range of chassis setup options. ★3mm thick carbon fiber.

Compatible Chassis
TA07 PRO Chassis

Information is correct as of December 11, 2017. Specifications are subject to change without notice.

Hop-Up Options no.1789

TA07 Carbon Stiffeners (Rear)

Item No: 54789

★Install in place of kit standard K1 and K2 parts. ★Stiffeners boost rear rigidity for stable performance. ★Use them to enhance your range of chassis setup options. ★3mm thick carbon fiber.

Compatible Chassis
TA07 PRO Chassis

Information is correct as of December 11, 2017. Specifications are subject to change without notice.

Hop-Up Options no.1792

R/C Model Polycarbonate Body Reinforcing Mesh Tape

Item No: 54792

★This mesh tape protects your polycarbonate body from inside. ★Use to protect vulnerable areas such as front spoiler, fenders and rear bumper. ★First paint the body from inside, then apply the tape over the paint. ★Use with Item 87190 R/C Model Polycarbonate Body Reinforcing Cement for even greater effect! ★35mm x 2m

Information is correct as of December 11, 2017. Specifications are subject to change without notice.

Finishing Materials No.190

R/C Model Polycarbonate Body Reinforcing Cement

Item No: 87190

★Use to reinforce your R/C model's polycarbonate body. ★Use with Item 54792 R/C Model Polycarbonate Body Reinforcing Mesh Tape for even greater effect! ★Can be used to attach separate polycarbonate light case parts. ★Applicator is included. ★Synthetic rubber cement. ★100ml aluminum tube.

Information is correct as of December 11, 2017. Specifications are subject to change without notice.