Item No:58729

All Electric R/C Car Series No.729

1/10 R/C OPEL KADETT GT/E (MB-01)

This R/C model assembly kit recreates the GT/E, a high-spec version of Opel’s 1970s hit car the Kadett, with a polycarbonate body depicting the classic 2-door form. The model is based upon the MB-01 chassis, a versatile platform which can be assembled as front- or rear-wheel drive and in one of three wheelbases.

Information is current as of March 5, 2024. Specifications are subject to change without notice.

All Electric R/C Car Series No.731

1/10 R/C 1997 MERCEDES-BENZ CLK-GTR (TC-01 CHASSIS)

Item No:58731

This R/C model assembly kit recreates the Mercedes-Benz CLK-GTR car which took six wins in dominating the 1997 FIA GT Championship. Although inheriting the 2-door coupe form and front section of its base road car, the racecar looked rather different and that aerodynamically honed form is recreated by a polycarbonate body, while separately molded components are used for the nose emblem, A pillar-mounted side mirrors, rear spoiler and rear wing. A full sticker sheet recreates this successful car's livery to round off the model.

TC-01: Seriously Low-Profile
This durable composite monocoque-frame chassis provides shaft driven 4WD from a central motor via front and rear propeller shafts, with oil filled gear differentials. 4-wheel independent double wishbone suspension employs long arms, plus inboard setups front and rear with oil dampers actuated by push rods and rocker arms to allow the use of low-profile bodies. Adjust spacer width to easily alter camber, skid and toe angle settings. Both suspension arms and uprights are identical left, right, front and rear, for more efficient pit work.

Specifications
★Length: 470mm, width: 194mm, height: 115mm ♦Wheelbase: 257mm ♦Tread: 159mm (front), 163mm (rear) ♦Tire width/diameter: 26/67mm (front & rear) ♦Composite monocoque-frame chassis ♦Midship motor, shaft-driven 4WD ♦Front & rear oil-filled gear differentials ♦3-piece steering tie-rod ♦Front & rear inboard 4-wheel independent double wishbone suspension ♦CVA oil dampers (front & rear) ♦Gear ratio = 7:50:1~5.25:1 (6.56:1 with kit 24T pinion) ♦Type 540 motor and electronic speed controller (ESC) are sold separately.

Separately Required Items
♦Type 540 motor ♦2-channel R/C system w/ESC ♦R6/AA/UM3 batteries for transmitter ♦Battery pack & charger

Information is current as of February 5, 2024. Specifications are subject to change without notice.

Hop-Up Options No.2086

4x18mm TITANIUM TURNBUCKLE SHAFTS

Item No:22086

These lightweight and rigid titanium turnbuckle shafts offer excellent durability from wear and tear. They can be used as turnbuckle upper arms on the TA08R, TA08 PRO and TB EVO. 8 chassis.

Information is current as of January 31, 2024. Specifications are subject to change without notice.

All Electric R/C Car Series No.737

1/10 R/C HOTSHOT II (2024)

Item No:58737

This model is a re-released and updated version of the 4WD buggy Hotshot II, the original of which was released in 1987. It employs CVA oil dampers II in the four-wheel double wishbone suspension, a front stabilizer, plus differential gears in the sealed gearboxes front and rear. Hybrid oval block/pin spike tires provide plenty of grip.

Information is current as of January 31, 2024. Specifications are subject to change without notice.

All Electric R/C Car Series No.733

1/10 R/C TOYOTA SUPRA (JZA80) (BT-01)

Item No:58733

The fourth generation Supra (JZA80) makes an appearance on our new 2WD chassis: the BT-01 offers a choice of front- and rear-wheel drive setups, with the latter having FR (front motor) and MR (midship-rear motor) options. It can also be set up with 251mm and 257mm wheelbases, and has unitized sections to make it easier to work on your car.

Information is current as of January 31, 2024. Specifications are subject to change without notice.

All Electric R/C Car Series No.730

1/10 R/C TOYOTA CELICA GT-FOUR RC (ST185) (TT-02)

Item No:58730

The Toyota Celica GT-Four RC was developed as a homologation car to take part in global rally races and in 1992, 5,000 units were sold around the world. ♦The glamorous form of the car is recreated by a polycarbonate body. ♦White five-spoke wheels are paired with radial tires.

Information is current as of January 31, 2024. Specifications are subject to change without notice.

Other No.227

ANTI-SLIP STICKER (75x150mm)

Item No:87227

This anti-slip sticker is perfect for a range of modeling uses, from sticking it on the underside of a display base to using it on tools such as your cutting mat or ruler. You can even add it to tweezer tips for enhanced pickups! It can be cut to your desired size using scissors.

Specifications
Size: 75mm x 150mm. Thickness: 0.5mm (excluding backing film). Highly adhesive double-sided tape on the reverse ensures the sticker stays in place.

Directions for use
1. Make sure the target surface is free of dust, moisture, oil and the like.
2. Cut the sticker to size, remove the backing film and apply it to the target surface.
3. Dust build-up can impact the anti-slip effect. Be sure to clean around the area regularly. Remove any dust with tape, etc.

Information is current as of January 10, 2024. Specifications are subject to change without notice.

Limited Edition Static Model Products

1/35 GERMAN TANK PANZERKAMPFWAGEN IV Ausf.G EARLY PRODUCTION & MOTORCYCLE SET "EASTERN FRONT"

Item No:25209

Ready to Make a Diorama?
The Pz.Kpfw.IV was used by German forces throughout WWII, and its Ausf. G variant was particularly notable as the first long-barreled version of this workhorse tank. Manufactured between March 1942 and June 1943, one of the identifying features of early production Ausf.G vehicles was the rounded muzzle brake. For beleaguered German units trying to take on powerful Soviet T-34s on the Eastern Front, the Ausf.G must have been a welcome arrival. The 2-stroke 350cc engine motorcycle was light and nimble, suiting it well to use in the rugged terrain and often punishing weather conditions on the Eastern Front; it was used for both reconnaissance and dispatch missions, and in fact saw service wherever German troops were in action.

About the Set
♦This is a 1/35 scale plastic model assembly kit set. ♦Length: 187mm, width: 54mm (Pz.Kpfw.IV Ausf.G) ♦Length: 54mm (motorcycle) ♦In-depth research of the actual vehicle ensures that the powerful Pz.Kpfw.IV Ausf.G form is captured in style. ♦The motorcycle is realistically depicted and features an ergonomic parts breakdown. ♦Three tanker figures, a rider for the motorcycle, and an officer figure are included. ♦The set comes with two marking options for Eastern Front vehicles.

Information is current as of January 29, 2024. Specifications are subject to change without notice.

Hop-Up Options No.2089

BB-01 ALUMINUM DAMPER MOUNT BAR (REAR)

Item No:22089

Installed in the roll cage under the roof, this aluminum bar gives more secure damper attachment and boosts chassis rigidity, contributing to greater rear traction and stable handling. Damper mount bar and adapters have a silver anodized finish.

Information is current as of January 29, 2024. Specifications are subject to change without notice.

Hop-Up Options No.2088

BB-01 ALUMINUM DAMPER STAYS (FRONT)

Item No:22088

Used in place of standard plastic A27 parts, these aluminum damper stays give more secure front damper attachment and enhance steering feel. Slimline and given a silver anodized finish, they will also make a cool addition to your model. Small components such as 5mm ball posts, O-rings, screws and aluminum spacers are also included.

Information is current as of January 29, 2024. Specifications are subject to change without notice.