TQ R/C & Hobbies

This is the S9452 Digital Hi-Speed.Hi-Torque Servo for many applications,
especially, On-Road Touring Car Use and Comes with "J" Connector Installed.
This servo is designed to be used with 6V receiver packs.

This servo replaced the S9451 servo.

FEATURES: Digitally Enhanced Microprocessor Cut About half the Response Time
From Transmitter Input To Servo Reaction.
Coreless Motor with two ball bearings on output shaft
Metal Gears (to replace, use FUTM3432)
High Torque
Case is Made of Black Plastic with newly developed mounting flanges
Dust and Water Resistant (Not Waterproof)
One year warranty

INCLUDES: One Digital Car/Boat Servo w/Small Round Horn
Two Rectangular Grommets
Four Brass Bushings (eyelets)
One Small Round Horn (already mounted on the servo)
One Three Arm Horn
Order FUTM2250 if mounting screws are needed

SPECS:    Speed: .13 sec/60° @ 4.8V
.11 sec/60° @ 6V
Torque: 102 oz-in (7.4 kg/cm) @ 4.8V
128 oz-in (9.2 kg/cm) @ 6V
Weight: 1.8oz (50g)
Dimensions: 1.6 x 0.8 x 1.4" (40 x 20 x 34mm)

COMMENTS: S9451 Digital Servo Precautions,
-It is best to avoid long leads and Y-harnesses especially with
standard grade wires. If problems are encountered, consider using
heavy duty wire such as Futaba's Heavy Duty Series or Hobbico's
Pro Series, minimizing lead lengths, and/or removing Y-harnesses.
Please Review The Following Points.
(1) When Using Systems With the Battery Fail Safe Function it Has
a Higher Cut-Off Voltage Setting Which Will Cause Shorter
Operation Time.
(2) When Installing the Servo Please Check Pushrod Linkage To Make
Sure There Is No Binding in Order To Prevent Excessive Power
Consumption and Decrease the Life of the Motor and Battery.

This digital servo cannot be used with the following * AM *
transmitters as the servo neutral signal is: 1310us).
CONQUEST AM, FG Series (T4FG, T5FGK,T6FG, T6FGK, T7FGK), New Terratop,
T3EGX, T3PGE, T2NL, T2LGX, T2FR, T2PK series.

For full performance of digital servos, please use them only with FM,
PCM, and HRS systems. Do not use digital servos with AM systems.

This is the Futaba S9353 High Voltage, High Torque, High Speed Servo

FEATURES: Designed to be used with models requiring especially high torque and
high speed
Metal casing helps dissipate heat
One year limited warranty through Hobby Services beginning at
date of purchase

INCLUDES: Futaba S9353 Servo with  1.7" (43mm) 3-point Horn, 3x8mm Servo Horn
Screw, four Eyelets, two Rubber Grommets and Instruction Sheet

SPECS:    Speed: 0.07 sec/60° at 6.6V
0.06 sec/60° at 7.4V
Torque: 272 oz/in (19.6 kg/cm) at 6.6V
305.6 oz/in (22.0 kg/cm) at 7.4V
Size: 1.59 x 0.83 x 1.47" (40.5 x 21 x 37mm)
Weight: 2.72oz (77g)
Power Supply: DC 6.0 - 7.4V
Horn Screw Size: 3x8mm
COMMENTS: Must be used with 2.4GHz radio systems for full performance

This is the S9352HV High Torque/High Speed Digital Servo from Futaba.

FEATURES: Designed to be used with models requiring especially high torque and
high speed
One year limited warranty through Hobby Services beginning at date of
purchase

INCLUDES: Futaba S9352HV Servo with 1.7" (42.3mm) 3-Point Horn, 3x8mm Horn
Screw, four Eyelets, two Rubber Grommets and Instruction Sheet

REQUIRES: Power supply of 6.0 - 7.4V

SPECS:                    6.6V                     7.4V
Speed:     0.07 sec/60°             0.06 sec/60°
Torque:    272.2oz/in (19.6kg/cm)   305.6oz/in (22kg/cm)
Size: 1.59 x 0.83 x 1.47" (40.5 x 21 x 37.4mm)
Weight: 2.54oz (72g)
 

COMMENTS: Must be used with 2.4GHz radio systems for full performance

This is a High Torque, High Speed Digital Mini Servo from Futaba.

FEATURES: Coreless motor: conventional servo motors have a steel core armature
wrapped with wire that spins inside magnets. In a coreless design
the armature uses a wire mesh that forms a cup that spins around
the outside of a magnet. This arrangement is much lighter, which
results in smoother operation and faster response time.
Nylon Gears
Can be used with 1/12 or 1/18 scale vehicles and electric helicopters
One year warranty

INCLUDES: One servo w/ 4 rubber grommets and brass eyelets, and one .83" (21mm)
diameter round horn
Instruction/Precaution sheet
Warranty Card

SPECS:    Dimensions: 1.4 x 0.6 x 1.1" (36 x 15 x 29mm)
Weight: .92oz (26g)
SPEED: 0.14 sec/60° @ 4.8V
0.11 sec/60° @ 6.0V
TORQUE: 50 oz-in (3.6 kg/cm) @ 4.8V
63 oz-in (4.5 kg/cm) @ 6.0V

COMMENTS: Will NOT work with these Futaba radios (4FG, 5FG/K, 6FG, 6FG/K, 7FG/K
New Terratop, 3EGX, 3PGE, 2NL, 2LGX, 2FR, 2PK series)
These radios have a servo neutral signal of 1310us not compatible
with this servo.
***For MAXIMUM performance, a 6.0V battery is recommended***

This is the S3152 Digital Servo w/Ball Bearings for
airplane, car and boat Use and Comes with "J" Connector Pre-Installed.

FEATURES: Comes with Heavy Duty wiring that can handle Higher Current Loads
Ball Bearing Output Shaft
Nylon gears
High Torque
Great for 1/8 Cars or Boats Where Higher Torque and Speed are Needed
One year limited warranty

INCLUDES: One Digital High Torque Servo w/Small Round Horn and 11.5" (292mm)
wire lead
Four Rectangular Grommets
Four Chrome Bushings
Four Mounting Screws
One Large Round Horn
One Six Arm Horn
One Four Arm Horn

SPECS:    Speed:  .22 sec/60° @ 4.8V
.18 sec/60° @ 6V
Torque: 70 oz-in @ 4.8V
87 oz-in @ 6V
Weight: 1.5oz (41g)
Dimensions: 1.6 x 0.8 x 1.5" (40 x 20 x 38mm)

COMMENTS: For a replacement gear set, order FUTM3328
For a replacement case set, order FUTM2948

S3152 Digital Servo Precautions,
-It is best to avoid long leads and Y-harnesses especially with
standard grade wires. If problems are encountered, consider using
heavy duty wire such as Futaba's Heavy Duty Series or Hobbico's
Pro Series, minimizing lead lengths, and/or removing Y-harnesses.
-Current Drain:  Futaba S3152 Servo is Specially Designed for High-
Torque and High-Speed, Therefore Very High Current Drain Is Normal
At Startup. For Ultimate Performance When Using This Servo
Please Review The Following Points.
(1) When Using Systems With the Battery Fail Safe Function it Has
a Higher Cut-Off Voltage Setting Which Will Cause Shorter
Operation Time.
(2) When Installing the Servo Please Check Pushrod Linkage To Make
Sure There Is No Binding in Order To Prevent Excessive Power
Consumption and Decrease the Life of the Motor and Battery.
This digital servo cannot be used with the following * AM *
transmitters as the servo neutral signal is: 1310us).
CONQUEST AM, FG Series (T4FG, T5FGK,T6FG, T6FGK, T7FGK), New Terratop,
T3EGX, T3PGE, T2NL, T2LGX, T2FR, T2PK series.

***** Do not use digital servos with older AM systems *****

This is the Futaba S3151 Digital Servo.
Great for a wide variety of R/C models.

FEATURES: Digital technology gives performance advantage
One Ball Bearing and one Metal Bushing
Nylon gears
One year warranty

INCLUDES: One S3151 Digital servo with preinstalled servo horn
Four Rectangular Grommets
Four Mounting Screws
One Large Round Horn
One Six Arm Horn
One Four Arm Horn

SPECS:    Speed:  0.21 sec/60° @ 4.8V

Torque:   43 oz-in  @ 4.8V
Dimensions:  1.6 x 0.8 x 1.4 in (41 x 20 x 36mm)
Weight: 1.5oz (42g)

This is the 2.4GHz FASST R614FS 4-Channel Receiver used with the
Futaba 4PKS Surface Radio System from Futaba.

FEATURES: Normal and high-speed modes for analog or digital servos including
the BLS series
One year limited warranty through Hobby Services beginning at date of
purchase

INCLUDES: 2.4GHz FASST R614FS 4-Channel Receiver with Instruction Manual
Internal and External antennas

SPECS:    Size: 1.38 x 0.91 x 0.33" (35.1 x 23.2 x 8.5mm)
Weight: 0.28oz (7.8g)
Operating Voltage: 3.5 - 8.4V
Current Drain: 135mA or less
Antenna Length: 8"

COMMENTS: Futaba FASST system does not work with current Futaba S-FHSS/FHSS
systems

This is the R614FF 2.4 GHz FASST Receiver
for use with the Futaba 2.4GHz 4PK and 4PKS Surface Radio System.

FEATURES: Futaba's FASST (Futaba Advanced Spread Spectrum Technology) shifts
very quickly virtually eliminating signal conficts and
interruptions unlike other 2.4GHz systems that only stay on one
or two frequencies.
Small and lightweight, for surface use only
One year limited warranty through Hobby Services beginning at date of
purchase

INCLUDES: Futaba R614FF 2.4 GHz FASST Receiver
Single external antenna

REQUIRES: Linking to transmitter

SPECS:    Size: 1.38 x 0.91 x 0.33" (35.1 x 23.2 x 8.5mm)
Weight: 0.28oz (7.8g)
Operating Voltage: 3.7V~7.4V / Usable voltage :3.5~8.4V
Antenna Length: 8"